See it in actionBook a demo →

Pool chemical calculator

Type in your test results and get what to add, how much, and in what order, plus the water's Langelier Saturation Index before and after. It's the same math our technician app uses on every stop.

gal
°F
ppm

Your readings and targets

Targets start as suggestions that bring the LSI to 0 to +0.3. Change any of them. Leave a reading blank if you didn't test it.

NowTargetFree chlorine
ppm
ppm
pH
Total alkalinity
ppm
ppm
Calcium hardness
ppm
ppm
CYA (stabilizer)
ppm
ppm
Salt (salt pools)
ppm
ppm

The products you use

pH up uses soda ash, alkalinity up uses baking soda, and stabilizer is cyanuric acid.

Water balance (LSI)

Now

-0.08

Slightly corrosive

With targets

+0.03

Balanced

Corrosive0 to +0.3 balancedScaling

Ring: your water now. Dot: with your targets.

A little on the aggressive side. Not urgent, but nudge pH or alkalinity up at the next visit.

What to add

  1. 1

    Raise alkalinity 70 → 90

    4.2 lbs Baking soda (sodium bicarbonate)

  2. 2

    Lower pH 7.9 → 7.7

    6 fl oz Muriatic acid (31.45%)

    Also lowers alkalinity about 1.6 ppm

  3. 3

    Raise calcium 180 → 275

    17 lbs Calcium chloride (77%)

  4. 4

    Raise free chlorine 1 → 3

    31 fl oz Liquid chlorine (12.5%)

    Adds about 3.3 ppm salt

Add one product at a time with the pump running and let it circulate before the next. Retest before adding more.

Get these doses on every stop, in your own products

In the Pool Founder technician app, the Balance card reads the readings your tech just entered and lists each dose in the products your company stocks, at their real strength and scaled to that pool's volume. One tap adds a dose to the visit's Chemicals Used. It runs on the phone, so it works without signal.

How the Langelier Saturation Index works

Every pool's water is either dissolving calcium carbonate or depositing it. The Langelier Saturation Index (LSI) puts a number on which way it's leaning. At 0 the water is exactly saturated: it leaves plaster alone and drops no scale. Below 0 it pulls calcium out of plaster, grout and pebble finishes and attacks metal. Above 0 it pushes calcium carbonate out of solution as scale on tile, in heaters and on salt cells.

The textbook formula adds up five factors: LSI = pH + TF + CF + AF − TDSF. TF is the temperature factor, CF the calcium factor (the log of calcium hardness, minus 0.4), AF the alkalinity factor (the log of carbonate alkalinity) and TDSF the dissolved solids constant, about 12.1 for typical pool water at 1,000 ppm. pH carries the most weight: 0.1 of pH moves the LSI by 0.1, while calcium has to double to move it by 0.3.

This calculator runs the full chemistry instead of the rounded chart: activity coefficients from ionic strength, calcium ion pairing, temperature curves for the carbonate constants, and alkalinity corrected for cyanuric acid. Stabilizer adds to the total alkalinity reading without buffering anything, so a pool at 80 ppm alkalinity and 60 ppm CYA has roughly 60 ppm of carbonate alkalinity doing the work. The model is checked against Orenda's public calculator and lands within 0.01 of it on hundreds of recorded readings, so it can read a few hundredths lower than a paper chart on stabilized or salt water.

Typical ranges

  • LSI: 0 to +0.3 balanced; −0.3 to 0 slightly corrosive; +0.3 to +0.5 slightly scaling; below −0.3 corrosive; above +0.5 scaling.
  • pH: 7.4 to 7.8. The suggestions aim for 7.5 to 7.6.
  • Total alkalinity: 70 to 140 ppm, usually targeted at 80 to 100.
  • Calcium hardness: at least 200 ppm for plaster; 250 to 400 is common.
  • CYA: 30 to 50 ppm outdoors, higher for salt pools.
  • Free chlorine: at least 3 ppm and at least 10% of your CYA. At 50 ppm CYA, keep 5 ppm.

How the doses are figured

Most doses are a rate times the change times the volume: amount = ppm change × rate per ppm per 10,000 gal × (gallons ÷ 10,000), adjusted for the product's strength. Raising free chlorine 1 ppm in 10,000 gallons takes about 10.2 fl oz of 12.5% liquid chlorine; 10 ppm of alkalinity takes about 1.4 lbs of baking soda; 10 ppm of calcium about 1.2 lbs of 77% calcium chloride. pH is different: how much acid or soda ash it takes depends on the alkalinity, so the calculator solves the carbonate chemistry instead of using a flat rate. Calcium, CYA and salt only come down by draining and refilling.

Safety

  • Add chemicals one at a time, with the pump running, and let each circulate before the next. Never mix two products in the same bucket.
  • Keep acid and chlorine apart, in storage and in the pool. Together they release chlorine gas.
  • When you dilute acid, add the acid to the water, never water to the acid. Pour it slowly into the deep end, away from the skimmer and from people.
  • Pre-dissolve calcium chloride in a bucket of water, and add it slowly: it gets hot.
  • Wear gloves and eye protection, follow the product label, and retest before adding more. A calculator can't see a bad test or an old jug of chlorine.

Make Monday easier than last Monday.

30-day free trial. No credit card required. Cancel anytime.